SCAN A10 Specifications

Digital Monochrome and Color Progressive Scan Cameras CV-A10 CL CV-A70 CL Operation Manual Camera: CV-A10CL Revision C CV-A70CL Revisio

CV-A10 CL and CV-A70 CL 6.2. Sensor Layout and timing 6.2.1. CCD Sensor Layout The CCD sensor layout with respect to pixels and lines used in the tim

CV-A10 CL and CV-A70 CL 6.2.2. Horizontal timing The LVAL period is shown for normal continuous mode. 1 clock = 27.66 ns Fig. 14. Horizontal timing

CV-A10 CL and CV-A70 CL 6.2.4. Partial Scanning The FVAL period is shown for 1/2 partial scan in normal continuous mode. 1 line = 26.7 µs Values f

CV-A10 CL and CV-A70 CL 6.3. Input/Output of Timing Signals For switch settings, please refer to chapter “7.1. Switch setting by internal switch.” 6

CV-A10 CL and CV-A70 CL 1 clk period = 27.7 ns Fig. 20. HD to LVAL timing for ext. synchronization 1 HD or LVAL period = 26.7 µs Fig. 21. Ext.

CV-A10 CL and CV-A70 CL 6.4. Operation Modes This camera can operate in 5 primary modes. 1. TR=0 Normal continuous Mode. Pre-selected exposure. 2

CV-A10 CL and CV-A70 CL 6.4.1. LVAL synchronous accumulation With LS=0, the accumulation will start synchronously with LVAL. The trigger pulse should

CV-A10 CL and CV-A70 CL 6.4.2. LVAL a-synchronous accumulation With LS=1, the accumulation will start immediately after the trigger leading edge. The

CV-A10 CL and CV-A70 CL 6.4.3. Continuous operation For applications not requiring asynchronous external trigger, but should run in continuous operat

CV-A10 CL and CV-A70 CL 6.4.4. Edge Pre-select Trigger Mode An external trigger pulse initiates the capture, and the exposure time (accumulation time

CV-A10 CL and CV-A70 CL Table of Contents 1. General...

CV-A10 CL and CV-A70 CL 6.4.5. Pulse Width Control Trigger Mode In this mode the accumulation time is equal the trigger pulse width. Here it is possi

CV-A10 CL and CV-A70 CL 6.4.6. Reset Continuous Trigger mode The RCT mode is in principle the same as normal continuous mode. The difference is that

CV-A10 CL and CV-A70 CL 6.4.7. Sensor Gate Control This mode is for applications with strobe flash illuminations or long time accumulations up to sev

CV-A10 CL and CV-A70 CL 6.5. Other Functions. Scanning. SC=0 through 3. The CCD scanning format can be selected between full or partial scanning. Wit

CV-A10 CL and CV-A70 CL Gain settings. AS=0, AS=1. The video gain can be selected between manual gain (AS=0), or AGC (AS=1). Manual gain is set by th

CV-A10 CL and CV-A70 CL LED for power and trigger. On the camera rear a Light Emitter Diode is found. The light will be green when power is connected

CV-A10 CL and CV-A70 CL 6.7. Save and Load Functions. The following commands are for store and load camera settings in the camera EEPROM. Load setti

CV-A10 CL and CV-A70 CL 7. Configuring the Camera 7.1. Switch setting by internal SW301 and SW302 SW 301 is used for communication port select and e

CV-A10 CL and CV-A70 CL 7.2. RS-232C control All configuration of the CV-A10 CL or CV-A70 CL camera is done via the RS-232C port on the 12 pin HR con

CV-A10 CL and CV-A70 CL 7.3. CV-A10CL/A70CL command list Command Name Format Parameter Remarks A – General settings and useful commands

CV-A10 CL and CV-A70 CL 1. General This manual will cover the digital monochrome progressive scan camera CV-A10 CL, and its color version, CV-A70 CL.

CV-A10 CL and CV-A70 CL 8. Camera Control Tool for CV-A10CL/A70CL From www.jai.com Camera Control Tool for Windows 98/NT/2000 can be downloaded. The

CV-A10 CL and CV-A70 CL 8.2. Camera Control Tool Interface The Camera Control Tool Software is based on a main Tool Bar and a number of associated

CV-A10 CL and CV-A70 CL RS-232 communication: 1. Select ’COM-ports’ from the ’CL Manufacturer/COM-ports’ list Box. 2. Select the communication port

CV-A10 CL and CV-A70 CL Factory and User Settings Use the Store button to store the current camera settings into the user settings area in EEPROM. C

CV-A10 CL and CV-A70 CL 9. External Appearance and Dimensions Fig. 38. Outline. 10. Specifications 10.1. Spectral sensitivity CV-A70CL is with an

CV-A10 CL and CV-A70 CL 10.2. Specification table Specifications CV-A10 CL CV-A70 CL Scanning system Progressive scan Frame rate full frame 60

CV-A10 CL and CV-A70 CL 11. Appendix 11.1. Precautions Personnel not trained in dealing with similar electronic devices should not service this camer

CV-A10 CL and CV-A70 CL 12. Users Record Camera type: CV-A10 CL/CV-A70 CL Revision: (Revision C) Serial No. …………….. Firmware version. …

CV-A10 CL and CV-A70 CL 4. Locations and Functions 6 6 5 4 3 2 1 1 Lens mount of C-mount type. *1) 2 Interline-transfer CCD sensor. 3 Camera L

CV-A10 CL and CV-A70 CL 5. Pin Assignment 5.1. 12-pin Multi-connector (DC-IN/Trigger) Type: HR10A-10R-12PB-01 (Hirose) male. (Seen from rear of came

CV-A10 CL and CV-A70 CL 5.3. Input and output circuits In the following schematic diagrams the input and output circuits for video and timing signals

CV-A10 CL and CV-A70 CL 5.3.5. Camera Link interface The video output is Camera Link with 10 or 8 bit video placed in a base configuration. The digit

CV-A10 CL and CV-A70 CL 6. Functions and Operations 6.1. Basic functions The A10CL-A70CL camera is a progressive scan camera with 10 or 8 bit video

CV-A10 CL and CV-A70 CL 6.1.3. CV-A10 CL. Binning Binning is only on CV-A10 CL. The binning functions can be used for higher frame rate or for high